| EzyLock Replacement Shaft |
With the Tormek EzyLock, which is both a nut and a washer, you need no tools for mounting and dismounting the stone. The special pitch on the left hand thread causes the rotation of the wheel to tighten the nut to the right torque.
Turn the Ezylock anticlockwise by hand and the grindstone will automatically tighten during the first sharpening. You need no tools.
When dismounting, you turn the stone clockwise and the EzyLock will automatically become loose.
This construction also makes it very easy to change grindstones, from the standard aluminum oxide to the new specialty stones (Blackstone Silicon for High Speed Steel and the 4000 Grit Japanese Waterstone).
The shaft, washer and EzyLock are all made of stainless steel.
Fits Tormek T-7, Tormek 2000 and all older models with 250 mm (10") stone.
Requires replacement of main shaft. |
    |
|
|
|
|
|
| Vertical Glue Press |
Are you tired of buckled panels and messy gluing tables?
The PLANO Vertical Glue Press will keep your valuable floor and bench space clear, while automatically assuring you of a well-laminated, flat panel or board, every time. And you won’t even need dowels or biscuits!
Why PLANO is your BEST solution for gluing solid wood panels.
- PLANO produces a superior quality glued-up panel.
Unique, patented PLANO design provides pressure on both edges and both faces of the project, creating superior quality joints and completely eliminating buckled panels.
- PLANO can handle almost any size panel you need.
- Thickness: PLANO’s linking arms automatically adjust to any board thickness from 0+ up to 5”.
- Length: limited only by the length of the wall where you mount your PLANO, and by number of mounting rails you have installed (onto which you hang your PLANO clamps). Just butt one 39.37” (1000mm) mounting rail next to another: the final rail can be easily cut off to suit your exact requirements, if needed. We recommend one PLANO clamp for every 12” of rail.
- Width: PLANO clamps are available in three heights: the original 43” (1100mm), the expanded 49” (1250mm), and the latest addition to the program, the 55” (1400mm) clamp. Clamp height determines maximum clamping width, since panels are held on their side in the PLANO system. All sizes let you clamp a single large panel or multiple narrower panels at one time, up to the total capacity of the clamp. To clamp several smaller panels edge-to-edge, simply leave out the glue between the last and first boards, respectively, of the adjacent panels.
Note: The shorter the clamp, the easier it is to load and unload. We therefore recommend you order only the height you will actually need, to ensure that using your PLANO will be as easy and convenient as possible!
- PLANO is maintenance-free.
PLANO clamps are easily cleaned of glue residue and are designed to ensure a lifetime of consistent operation and professional-quality results.
- PLANO makes stronger joints than conventional clamps or less advanced systems.
Unlike pipe/bar clamps which invariably “pinch” slightly on the bar side, PLANO applies centered and even pressure to the gluing surface because it completely surrounds the joint, resulting in a stronger, better-looking joint even without the use of dowels or biscuits.
- PLANO saves you space.
Vertical wall mounting cuts the shop surface area required for gluing up with conventional bar clamps, gluing racks or gluing tables by up to 90%.
- PLANO saves you money.
Wide boards cost more and tend to warp; with your PLANO you can easily glue up more affordable narrow boards to produce wide, warp-resistant panels. And because Plano properly aligns your boards better, panels glue up flat and require less planing and surfacing, That lets you start the process with less surplus wood thickness, too, so you can save even more on your lumber purchases.
- PLANO saves time and effort.
- vertical position of panels makes loading easy and reduces drying time.
- properly set up, panels can never “rack”: your panels are always square.
- proper alignment of the boards (no buckling) saves hours of planing and sanding.
- Dowels and biscuits become unnecessary, further reducing cost and time.
|
|
|
|
|
| Narrow Profile Disc Set |
 Optional narrow profile disc set for the LA-120. Includes 2mm radius and 45 degree vee edges (standard set includes 3mm radius and 60 degree vee). |
|
|
|
|
| Leather Honing Wheel |
| The Leather Honing Wheel should last indefinitely, but accidents do happen and if you cut yours by forgetting to always work with the wheel turning away from the edge, here is the original factory replacement. |
|
|
|
|
|
|
|
YourCompany.com
Enlarged Lip
